Kugelrohr Distilling Bulb Capacity: 5, 10, 15, 25 or 50mL available Joints: 14/20, Bulb O.D.: 25, 31, 35, 42 or 48mm available Overall Height: 80, 85, 90, 98 or 105mm available Used in distillation of very small amount of distillate at lower temperature with high efficiency.

Distilling Head, Vacuum Jacketed Thermometer Joint: 10/18 Joints: 14/20 or 19/22 available For use with 25mm immersion thermometer.

Trap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. With two 4mm drain holes at the base of the inner tube to allow solvent to drain back into the evaporation flask. Has upper outer and lower inner standard taper joints.

Distillation Adapter, Microscale, Synthware, Joints: 14/10, supplied with one compression cap, one Viton O-ring and one PTFE-faced silicone septum.

Used with 25mm immersion thermometer, and D27 distillation receiver.

Synthware vacuum adapter with a serrated hose connection 180 degrees to the standard taper inner joint. The glass stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.

Connecting Tube, T-shaped, Synthware, Tubing OD: 8 and 10mm available.

Adapter #15 O-ring joint to 10 OR 16mm Hose Connection

With the condenser being a combination of a cold coil and Leibig. Top outer joint is a 10/18 for use with a 50mm immersion thermometer. With Vigreux Indentations.

Synthware vacuum adapter with a serrated hose connection turned 90 degrees to the standard taper outer joint. The PTFE stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.

Synthware vacuum adapter with a serrated hose connection turned 90 degrees to the standard taper inner joint. The glass stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.

Vacuum Adapter, Microscale, PTFE Stopcock, Synthware, Joint: 14/10, Stopcock Bore: 2mm, Hose Connection OD: 8mm.

Solvent Still Head Capacity: 500 and 1000mL available Top Joint: 24/40 Bottom Joint: 24/40 and 29/42 available Side Joint: 14/20 Drainage Port Joint: 14/20

Synthware distilling adapter with top compression cap. With same size standard taper inner joints on bottom and side arm. Cap accomodates 5.0 - 7.5mm O.D. thermometer. Supplied with one Nylon cap and one Viton o-ring.

Comes with Synthware Distilling Adapter (Joints: 14/20 or 19/22) and Cow Receivers (Joints: 14/20 or 19/22). Designed without hose connection to be used with D10 distillation apparatus. **NOTE THESE PRODUCTS COME IN DIFFERENT SIZES - WHAT IS PICTURED MAY NOT BE THE ITEM SOLD**

Thermometer Adapter, Microscale, Synthware, Joints: 14/10, Thermometer OD: 5.0-7.5mm, supplied with one compression cap and one Viton O-ring.

Synthware distillation connecting adapter. With standard taper top outer joint and inner joints at bottom and the side arm. Bottom and side arm joints are angled at 75 degrees to one another.

Synthware vacuum adapter with 2mm straight bore PTFE stopcock on the hose connection.The upper outer and lower inner standard taper joints are the same size.

Provides dual entry into a variety of flasks. Adapter has standard taper outer joints at top and on side and inner joint on bottom. All joints are the same size.

Adapter is placed above flask to prevent carry-over of reactions which have a tendency to foam. With top outer and lower inner standard taper joints.

One-piece design for easy set-up. For the best result, use D272440 distillation receiver. To be used with 25mm immersion thermometer.

Allows for flexible tubing to be connected to apparatus for introduction of vacuum or pressure. Hose connection is at a 90 degree angle to the standard taper inner joint.

Synthware inlet adapter with extended length lower tube. Allows for the introduction of reactants below the interior surface. Tube extends 153mm (6 inches) below the joint. Tubing has the same O.D. on both ends of the joint.

Synthware distillation adapter with sealed in drip tip. Adapter is bent at 105 degrees. Standard taper top outer joint and lower inner joints. 

Sublimator, Two Piece, Synthware, Various sizes are available. O-Ring Size: 217, 226, or 229, Clamp Size: 35, 65, or 75 available.

Snyder Distillation Column, 3 Section Top Outer Joint: 24/40 Lower Inner Joint: 24/40 Column Height: 150mm Overall Height: 300mm For use with Kuderna-Danish flask.

Distillation head with condenser sealed to a Vigreux column. Vacuum adapter has an outer joint and accepts a distribution adapter (D201414). To be used with a 25mm immersion thermometer.

Synthware vacuum adapter has a standard taper outer joint and a serrated hose connection. Ideal for use as a vent or for the introduction of pressure/vacuum.

Comes with Synthware Distilling Adapter (Joints: 14/20, 19/22 AND 24/40) and Cow Receivers (Joints: 14/20, 19/22, AND 24/40). Rotating cow receiver allows four flasks to be progressively filled. **NOTE THESE PRODUCTS COME IN DIFFERENT SIZES - WHAT IS PICTURED MAY NOT BE THE ITEM SOLD**

Synthware reducing adapters are used for connecting dissimilar standard taper joint sizes. The lower inner joint is larger in size than the top outer joint.

Hickman-Hinkle Still Head, with Side Port, Synthware, Joint: 14/10, for microscale fractional distillation, supplied with one compression cap, one Viton O-ring and one PTFE-faced silicone septum.

Vacuum Takeoff Adapter, Microscale, Synthware, Joint: 14/10, supplied with one compression cap, one Viton O-ring and one PTFE-faced silicone septum.