Ace Glass Stirrers
-
Button type, solid glass stirring shafts, 5 & 6mm OD. Precision ground shafts, codes -04 & -06, should be used in matching glass Trubore 9524 and 9527 bearings. Polished shaft, code -40, should be used only in our 8066-120, 6mm PTFE inner bearing. All accept our 9542 blades. Join to stirrer motor…
-
Precision ground glass stirring shafts, 10mm OD, paddled, button type and bead type. Button type shafts accept 8083, 8085, 8086, 8087 & 8096 stir blades. Beaded shafts accept 8088, 8089, 8090 & 8091 agitators. Use with Trubore bearings 8036, 8038, 8039, 8040, 8042, 8043, 8047, 8051, 8053 & 8055.…
-
Stirrer, Complete
Ace GlassPrecision Trubore Stirrer Assembly consisting of 10 mm ID bearing, bushing, precision ground, button type glass shaft and blade. Available with either glass or PTFE stir blade.
-
Fully flexible drive shaft facilitates isolation of the stirrer motor from the reactor. Complete units, code -30 (91.4cm) and code -32 (152.4cm), designed for use with 8mm (5/16in) motor shaft. Purchase the optional code -27 adapter for motors with 9.5mm (3/8in) shafts. Reactor end consists of a…
-
Agitator, PTFE, Turbine, For 10mm Shaft
Ace GlassAll-PTFE turbine type agitator. Unique locking arrangement assures positive grip. Agitator fits 10 mm shafts. Shaft opening is drilled straight thru to allow positioning of agitator at any drilled position on shaft as well as the bottom. For use with bead type glass shafts, 8068-G, 8075 or PTFE…
-
Stirring Shaft, Unground, 9mm
Ace GlassUnground, 9mm OD shaft for use in liquid seal bearings and our debris free 8098 and 8099 stirrer assemblies. Code -25 is a button type shaft which accepts our 8083, 8084, 8085 and 8086 blades. Shaft length accomodates flasks from 500ml to 5000ml.
-
Ultra-Vacuum stirrer bearing for applications up to 0.6 Torr. Non-shedding bearing is manufactured from PTFE, Rulon and PEEK materials. Equally good in both vacuum and pressure applications as low as 0.6 Torr. Rated for up to 400 rpm with both glass (polished rather than precision ground is best)…
-
Stirring shaft agitator combination available in either a solid, precision ground glass shaft or all PTFE knob type shaft with a PTFE snap-fit agitator designed to fit through 14/20 and 18/11 joints. Designed for use with our 5mm ID 9524 or 9527 bearings and flasks of 50ml and smaller.
-
Bearing, Trubore, High Vacuum, 10mm
Ace GlassThis bearing is the standard liquid seal type except that the use of Trubore tubing enables this unit to perform very satisfactorily under high vacuum conditions. Use our precision ground stirring shafts (8068,8070,8071,8073,9532,9533).
-
Stirring Shaft, Glass, Polished, 10mm
Ace GlassPolished glass stirring shafts, 10mm OD. Recommended for use with only our 8050,8066,13443 and 13445 bearings. Join 8083,8085,8086,8087,8096 blades to button type shafts. Join 8088, 8089, 8090 & 8091 agitators to bead type shafts. Plain shafts will accept 8094 & 8095 agitators secured with a…
-
Offset gearbox and motors complete with right angle drive unit for pilot plant systems. Motors with right-angle drive save headspace and work well where height is restricted. Available for standard or hazardous duty applications. Available in either 1/4hp or 1/2hp with a digital 115/230v 50/60Hz…
-
Precision ground glass stirring shafts, 19mm OD, hollow, heavy duty. Knob type shafts accept 8091,8092,8093,8100 agitators and can be used in all 19mm ID Trubore 8059, 8060, 8061 and 8065 bearings. Compatible with our 8050 mechanical seal and 13445 PTFE Debris-free bearings. Join to stirrer motor…
-
Stirrer, Complete
Ace GlassTrubore stirrer assembly consists of the standard taper outer glass bearing, PTFE inner bearing, glass-filled PTFE bushing and lock nut, compression seal saddle o-ring, PTFE blade and either a glass or stainless stir shaft.
-
Trubore bearing, heavy duty, standard taper joint, self-aligning. Unique 3 piece design of Trubore inner bearing, compression seal nylon bushing and glass standard taper adapter allows for moderate misalignment of stir motor and the bearing cannot sieze the shaft. For use with 8077 & 8078 19mm od…
-
Self-aligning, lubricant free PTFE Trubore bearing or combination bearing / debris trap. Use with 8074 stainless steel or 8075 polished 10mm od glass shafts. Debris trap model prevents bearing-wear particles from contaminating the reaction vessel and has a side port for clean-out, evacuating or…
-
Agitator, PTFE, Large scale, Turbine
Ace GlassA turbine type agitator, available for 19mm and 28mm shafts. 19mm six blade agitators are open in the center to allow custom positioning on drilled type or knob type 8076, 8078 & 8079 shafts. 28mm four blade agitators are supplied with a PTFE nut & bolt set for securing to 8080 shafts. Shaft is not included.
-
Stirring Blade, For 5 & 6mm Shaft
Ace GlassPTFE stirring blades for use with our button type 9524 and 9527 stirring shafts. Blades are 41mm wide x 12mm high and are designed for use in flasks 250ml and less. Match blade to shaft OD.
-
Polished stainless steel stirring shafts, 10mm OD, drilled type with removable button. When used with 8066 PTFE bearing, a lubricant-free vacuum seal can be realized at speeds up to 200 rpm. Recommended for use with 8044,8050,8066,13443 and 13445 bearings. With button, shaft accepts…
-
Agitator, PTFE, Large Scale Multi-blade
Ace GlassThese heavy-duty PTFE agitators impart maximum energy and are offset at the bottom to accomodate slurries. 10mm agitators fit drilled type or knob type 8068, 8071 & 8075 shafts. 19mm agitators fit drilled type or knob type 8076, 8078 & 8079 shafts. 28mm agitators fit 8080 drilled shafts.
-
Stir Shaft, 4 Blade Propeller, PTFE
Ace GlassPTFE covered stainless steel shaft with solid PTFE, 4 blade screw propeller. Blades are pitched 45 degrees. For a better grip by the stir motor chuck, 50mm of stainless is left exposed.
-
PTFE covered stainless steel stirring shafts, 10mm OD, drilled type. If used unlubricated, 500 rpm max with water cooled 8040 bearing, 100 rpm max recommended with 8036, 8038, 8039, 8043, 8047, 8051 and 8055 bearings. With condensate film as added heat transfer agent, 2000 rpm can be attained.…
-
Precision ground, hollow, 5mm glass stirring shaft. Button type shaft accepts 9542 blades and can be used in matching 9524 and 9527 bearings. Holes are provided in the side of the shaft for material introduction and at the bottom for emission into the flask contents. Join to stirrer motor using…
-
Stir Shaft, Retreat Agitator, PTFE
Ace GlassPTFE covered stainless steel shaft with a solid PTFE retreat curve agitator. Featuring a retreat angle of 30 degrees and, for a better grip by the stir motor chuck,50mm of exposed stainless.
-
3/8HP Brushless DC motor for use on pilot plant reactors up ²to 200L. May be used with either the 120V or 240V BLDC ²motor controllers. Supplied with 6ft removable cable and ²mounting hardware.
-
Bearing, Trubore, Ace-Thred, 10mm
Ace GlassSelf-aligning, three-piece bearing. Complete consists of inner Trubore bearing, Nylon bushing with O-Ring, and threaded adapter. Unique design eliminates costly replacement since inner bearing will spin if shaft binds or will self-align at O-Ring seal in the event the motor is slightly cocked.…
-
316 stainless steel, football shaped, stir blades for 10mm OD button type stir shafts. Holed versions, codes -70 thru -74, provide even greater agitation. 10mm OD stir shafts can be found in our 8068, 8070, 8074 and 8075 series.
-
PTFE banana shaped stir blades for 10mm OD button type stir shafts. 3mm thick blades have a number of perforations and are designed to closely fit various sizes of round bottom flasks. 10mm OD stir shafts can be found in our 8068, 8070, 8074 and 8075 series.
-
PTFE agitator with removable blade secured with a PTFE pin. Supplied 3.2x15.2cm blade will fit through a 45/50 joint. Fits 19mm od drilled type or knob type 8076, 8078 & 8079 shafts.
-
PTFE Gasket
Ace GlassDesigned to fit 8068, 8070, 8071, 8074 or 8078 stirring shafts. Useful as dust cover and as replacement for gasket supplied with 8127 collar. Twelve to a package.
-
Agitator, PTFE, 4 Blade
Ace Glass4 Blade PTFE agitator available with either 45 or 90 degree blade angle. For use with glass or metal shafts and is secured using a compression style fitting allowing it to positioned anywhere along the length of the shaft.
-
Stirrer Assembly, Vacuum, Debris Free
Ace GlassRotating ball joint seal gives vacuum-tight connection good into the micron range. Ultimate vacuum is determined primarily by the tightness of the vinyl tubing connector which fastens the unground shaft to the ball member. Operate below 500 rpm. Use with unground stirring shafts (8134,9530).…
-
PTFE, large-scale, multi-paddle agitator design to accept pinned bottom valves, like our 6482 flush-seal valve. The pin helps reduce wobble or flexing at higher rpm. 28mm agitators will fit drilled type 8080 shafts.