Kemtech America

Glass, Kemtech America

Compare Tool

Select up to 3 products

1 - 32 of 68
Sort
View
Show
  • Synthware Vacuum Adapters with Glass Stopcocks, 90°

    Kemtech America

    Synthware vacuum adapter with a serrated hose connection turned 90 degrees to the standard taper inner joint. The glass stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.

  • Synthware Vacuum Adapters with PTFE Stopcocks

    Kemtech America

    Synthware vacuum adapter with a serrated hose connection 180 degrees to the standard taper inner joint. The PTFE stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.

  • Synthware Tapered Distilling Adapters

    Kemtech America

    With an outer standard taper joint at the top. The tapered delivery drip tube extends into open receivers.

  • Synthware Vacuum/Inert Gas Adapters with Glass Stopcocks

    Kemtech America

    Synthware vacuum or inert gas adapter has a T-bore glass stopcock allowing vessels with a standard taper outer joint to purged and evacuated. The stopcock has a constant pressure retention device and a 4 mm bore.

  • SYNTHWARE Vigreux Distilling Columns

    Kemtech America

    Column length is measured from the highest to lowest indent in the column.

  • Synthware Vacuum Adapters, Outer Joint

    Kemtech America

    Synthware vacuum adapter has a standard taper outer joint and a serrated hose connection. Ideal for use as a vent or for the introduction of pressure/vacuum.

  • Synthware Rotary Evaporator Vapor Ducts

    Kemtech America

    Synthware rotary evaporator vapor duct. Precision ground and polished. Meet manufacturer's standards. With standard taper inner joint.

  • Synthware Inlet Adapters

    Kemtech America

    For use with gas inlet tubes or plain stem thermometers. Supplied with one holed rubber adapter.

  • Synthware Distillation Connecting Adapters

    Kemtech America

    Synthware distillation connecting adapter. With standard taper top outer joint and inner joints at bottom and the side arm. Bottom and side arm joints are angled at 75 degrees to one another.

  • Synthware Vacuum Filtration Adapters

    Kemtech America

    Used with plain stem Buchner funnels and pluro-stopper. Hose connector has an O.D. of 10mm at the largest serration. Joint is a standard taper inner joint. Pluro-stoppers are not included.

  • Synthware Distillation Adapters, 75°

    Kemtech America

    Synthware distillation adapter bent at 75 degrees. Both ends are standard taper inner joints and are the same size.

  • Synthware Rotary Evaporator Anti-Splash Traps, Modified

    Kemtech America

    Trap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. With two 4mm drain holes at the base of the inner tube to allow solvent to drain back into the evaporation flask. Has upper outer and lower inner standard taper joints.

  • Synthware Rotary Evaporator Anti-Splash Traps

    Kemtech America

    Trap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. With upper outer and lower inner standard taper joints.

  • Synthware Inlet/Thermometer Adapters

    Kemtech America

    Adapter has a Nylon compression cap and a Viton o-ring to form a vacumm tight seal. Cap accommodates 5.0 - 7.5mm O.D. thermometer or gas inlet tube. To use it as a syringe port, simply replace the o-ring with a PTFE-lined septum. Supplied with one Nylon cap and one Viton o-ring.

  • Synthware Vacuum Adapters with 1:5 Teflon® Stopcocks

    Kemtech America

    Synthware vacuum adapter with a serrated hose connection turned 90 degrees to the standard taper inner joint. The PTFE stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.

  • Synthware Distillation Adapters, Vacuum Jacketed

    Kemtech America

    Can be used as a distilling head to connect a condenser to the top of the distillation column. The 10/18 top joint accomadates a 76mm immersion thermometer.

  • Synthware Rotary Evaporator Anti-Splash Traps with Fritted Discs

    Kemtech America

    Synthware rotary evporator anti-splash trap with extra coarse fritted disc. Trap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. the frit reducesfoam from being carryover. With upper outer and lower inner standard taper joints.

  • Synthware Vacuum Take-Off Adapters with Glass Stopcocks

    Kemtech America

    Synthware vacuum adapter with 2mm straight bore glass stopcock on the hose connection.The upper outer and lower inner standard taper joints are the same size.

  • Synthware Vacuum Adapters with Outer Joints & Glass Stopcocks

    Kemtech America

    Synthware vacuum adapter with a serrated hose connection turned 90 degrees to the standard taper outer joint. The glass stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.

  • Synthware Claisen Adapters, Modified

    Kemtech America

    It is modified with an additional side arm at 45 degrees to the vertical outer joint. All joints are the same size.

  • U-Shaped Adapters

    Kemtech America

    Synthware U-shaped adapter. With standard taper inner joints at both ends.

  • Synthware Vacuum/Inert Gas Adapters with Ball Joint

    Kemtech America

    Allows for flexible tubing to be connected to apparatus for introduction of vacuum or pressure. Hose connection is at a 90 degree angle to the spherical ball joint.

  • Synthware Vacuum Take-Off Adapters, Short Stem

    Kemtech America

    Synthware vacuum take-off adapter with drip tip. For use in vacuum distillation. Adapter is bent at 105 degrees. Serrated hose connection is attached to vacuum source. With standard taper top outer joint and lower inner joint of the same size.

  • Synthware Distilling Adapters, 75°

    Kemtech America

    Synthware distilling adapter with top compression cap. With same size standard taper inner joints on bottom and side arm. Cap accomodates 5.0 - 7.5mm O.D. thermometer. Supplied with one Nylon cap and one Viton o-ring.

  • Synthware Distillation Adapters, Vigreux

    Kemtech America

    Synthware Vigreux distillation connecting adapter. Indenstations in lower section improve liquid/vapor contact. The standard taper top outer joint accomodates a 76mm immersion thermometer. Bottom and side joints are standard taper inner joints.

  • Synthware Flow Control Adapters with Metering Stopcock, 90°

    Kemtech America

    Synthware flow control adapter with metering stopcock. The serrated hose connection is turned 90 degrees to the standard taper inner joint. Provides on/off control with the main stopcock and precise control of liquids or gasses with the needle valve.

  • Synthware Bushing Adapters

    Kemtech America

    Synthware bushing adapters allow for compact assemblies of dissimilar standard taper joints.

  • Synthware Inlet Adapters with Hose Connection

    Kemtech America

    Adapter has a Nylon compression cap and a Viton o-ring to form a vacuum tight seal. Cap accommodates 5.0 - 7.5mm O.D. thermometer or gas inlet tube. The 8mm hose connection can be used for N2/Ar introduction or vacuum. Supplied with one Nylon cap and one Viton o-ring.

  • Synthware Flushing Adapters

    Kemtech America

    Synthware flushing adapter is used to flush and fill attached vessels with an inert gas to provide protective storage. A ballon is connected to the top hose connection. An inert gas is connected to the side hose connection. The ballon can be expanded with inert gas at the same time as the vessel or…

  • Synthware Distillation Adapters

    Kemtech America

    Adapter is bent 105 degrees. The top outer and lower inner standard taper joints are the same size.

  • Synthware Connecting Adapters

    Kemtech America

    Synthware combination adapting connector with a top spherical socket joint and a lower standard taper inner joint.

  • Synthware Vacuum Distilling Adapters

    Kemtech America

    With two standard taper inner joints that are parallel and at a 75 degree angle to the connecting tube. Distance between joints is 100mm.

Compare Tool

Select up to 3 products

Please Log In

Don't have an Account? Create one now.