General Lab Products
-
Bellco Heating Blanket 115V-6L 300 Watt
Bellco GlassHeating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Flask size: 6l Watts: 300 Dimension (in.): 3 x 22 1/4 Latches: 2 6 ft…
-
Stainless Steel Shaft Assembly 15-36L
Bellco GlassManufactured from 316l stainless steel. Impeller assembly for micro-carrier spinner flasks. 1965 series micro-carrier spinner flask Size: 15-36l
-
Removable baffle for large flange vessels. Material: SST 36l with electropolish finish Dimensions: 1 1/2" wide x 10 1/2" long Fits on any 1/4" od SST tube inside vessel Recommend: 2 per vessel Z-shaped
-
IOB Impeller Assembly 8L
Bellco GlassStainless steel shaft design prevents cell damage and minimizes magnetic decoupling. Sealed internal assembly requires less incubator space. For use with bellco 1965-series standard and water jacketed spinner flasks. Cap size: 100mm Flask size: 8l Paddle: 6 3/4" x 5"
-
Large Flange Round Bottom Vessel 3L
Bellco GlassHeavy walled construction for cell culture and fermentation applications. Heavy duty o-ring flange creates positive seal for stainless steel head-plate. For use with stainless steel head-plate, o-ring, and locking clamp. Use with CellTrol ii only single or dual systems, and speed control modules.…
-
Baffle Assembly 7L Large Flange
Bellco Glass316l stainless steel baffle assembly for use on large flange 7 liter bioreactor vessel system. Attaches to the head plate. used to change the mixing characteristics within the bioreactor. 3 required per vessel 1/4? rod Silicone 0-ring
-
The bellco sample system attaches to the headplate of a bioreactor allowing the user to take repeated aseptic samples into a standard 50ml disposable conical tube. The sampler is designed to connect to an existing pipe by mounting under the nut of a headplate stud. Samples are taken by evacuating…
-
Aldrich® corrosive lecture-bottle gas regulator
MilliporeSigma•Single-stage •CGA inlet connection, needle valve outlet with ¼ in. NPTM connection •Max. inlet pressure: 0-4000 psig •Temp. range: -40 to 140F •316 Stainless Steel body 1 ½ in. gauge face, PTFE seals and inner friction sleeves •NPTF bonnet-vent (1/8 in.) connection for piping regulator to…
-
Impeller Assembly 25mL
Bellco GlassGlass shaft impeller assembly for 1967-style hanging bar spinner flask. Consist of ptfe magnet holder and ptfe coated magnet. Glass shaft ptfe magnet Size: 25ml
-
Micro-Carrier Impeller Assembly 15-36L
Bellco GlassImpeller assembly for micro-carrier spinner flasks. Consist of magnet holder, silicone plug, magnet, and ptfe paddle. Impeller size: 15-36l Paddle dimensions: 3"x 10"
-
-
Stainless Steel Bent Harvesting Tube 36L 1/4"x20"
Bellco Glass316l stainless steel bent harvesting tube for 36l flat bottom omni vessel. Use with large flange head-plate. Size: 1/4" x 20" Id: 5/32"
-
Stainless Steel 2-Port Assembly 3L
Bellco GlassAll port assemblies are manufactured from 316l stainless steel and have an electropolish finish. 2- port assemblies have siphon and vent tubes. 3-port assemblies have siphon, fill tube and vent tubes. All port assemblies include a 45mm blue polypropylene screw cap and white silicone gasket. Size:…
-
Large Flange Omni Paddle 8L
Bellco GlassBlades and impeller assemblies are use for cell culture. Reduces shear in delicate cell culture. Manufactured from 316l stainless steel with electropolish finish. Ra 32 finish or better inside and out. Blade dimension: 5 3/4 x 2?. Shaft oal: 12 1/2?. Constructed of 316l electropolished stainless…
-
Impeller Assembly 15-36L
Bellco GlassGlass shaft impeller assembly for 1967-style hanging bar spinner flask. Consist of ptfe magnet holder and ptfe coated magnet. Glass shaft ptfe magnet Size: 15-36l
-
Stainless Steel Shaft Assembly 100mL
Bellco GlassManufactured from 316l stainless steel. Impeller assembly for micro-carrier spinner flasks. 1965 series micro-carrier spinner flask Size: 100ml
-
Dow Corning® high-vacuum silicone grease colorless
MilliporeSigmaSeals and prevents freezing of stopcocks and ground-glass joints in high-vacuum systems at pressures less than 10-6 mm Hg. Heat stable (-40 to 260 C), low vapor pressure, and chemically resistant. Colorless. 5.3 oz. tube. Legal Information: Dow Corning is a registered trademark of The Dow…
-
Straight Harvesting Tube 10L 1/4"
Bellco GlassMaterial: 316l stainless steel with ra finish of 32 inch or better, inside and out Dimensions: od x id:1/4? x 5/32? x 10.0? long
-
Stainless Steel Bent Harvesting Tube 5L 1/4"x16"
Bellco Glass316l stainless steel bent harvesting tube for 5l flat bottom omni vessel. Use with large flange head-plate. Size: 1/4" x 16" Id: 5/32"
-
Low Profile 3-Port Thermowell Assembly 6L
Bellco GlassThermowell assemblies are used to hold inside one tube the rtd temperature sensor that monitors the temperature within the vessel in conjunction with a temperature controller. There are also tubes for addition of media and vent tube. Port Thermowell assembly For low profile 3l vessel Material: 316l…
-
Stainless Steel Bent Harvesting Tube 8L 1/4" x 18"
Bellco Glass316l stainless steel bent harvesting tube for 8l flat bottom omni vessel. Use with large flange head-plate. Size: 1/4" x 18" Id: 5/32"
-
Stainless Steel 2-Port Assembly 6L
Bellco GlassAll port assemblies are manufactured from 316l stainless steel and have an electropolish finish. 2- port assemblies have siphon and vent tubes. 3-port assemblies have siphon, fill tube and vent tubes. All port assemblies include a 45mm blue polypropylene screw cap and white silicone gasket. Size:…
-
Stainless Steel 2- Port Assembly 500mL 100mm
Bellco GlassAll port assemblies are manufactured from 316l stainless steel and have an electropolish finish. 2- port assemblies have siphon and vent tubes. 3-port assemblies have siphon, fill tube and vent tubes. All port assemblies include a 45mm blue polypropylene screw cap and white silicone gasket. Size:…
-
All-purpose tweezer set
MilliporeSigmaContains 5 tweezers in a vinyl pouch: 41/2 in. dissecting tweezer, 43/4 in. stamp tweezer, 6 in. retrieving forceps, 6 in. solder utility tweezer, and 61/2 in. self-closing tweezer.
-
3-Port Harvest Assembly 15L
Bellco GlassSize: for standard ohd 15l vessel To fit gl45 vertical sidearms Material: 316l SST with electropolish finish, ra 32 or better, inside & out Dimensions:harvest tube (3/8"od)-1"above slug,16" insertion length, approx Addition tube (1/4"od) - 1" above slug, 2 21/64" below Vent tube (1/4" od) - 1"…
-
-
L-Bubbler Tube w/ Holes,8L (10) .040 Holes
Bellco GlassSparging accessory for vertical sidearm spinner flasks. Manufactured from 316l stainless steel with electropolish finish. Includes polypropylene cap with 1/4? white compression fitting and white silicone gasket. .040 inch hole for aeration of fermentation cultures where shear force is less…
-
Media Addition Bottle 2L
Bellco GlassHeavy walled construction for cell culture and fermentation applications. Heavy duty o-ring flange creates positive seal for stainless steel head-plate. For use with stainless steel head-plate, o-ring, and locking clamp.
-
PE, 1 to 1 1/2 gpm. Flexible discharge tube and hose hook with tapered adapter fit 1 to 5 gal containers or cans. Internal flapper valve prevents reverse flow.Uses: mild solvents, light oils, corrosives, dilute acid/caustics, liquid waxes, and disinfectants. Barrel: 21 in. L. Hose: 38 L x 1 in. diameter.
-
-
Compression Fitting 1/2in.
Bellco GlassBellco compression fittings are designed using our standard 45mm blue polypropylene open top caps and white silicone gaskets. A wide variety of fittings are available to allow ph and do monitoring via insertion of these probes into sidearms or vessels. Bellco probe adapters are designed to allow…
-
Screw Cap Assembly 51mm
Bellco GlassBlack phenolic screw caps are manufactured from specially formulated phenolic resin to resist the effects of temperature and steam autoclaving. They have a non-toxic white rubber liner for all general culture applications. Consists of screw cap liner and stopper or compression fitting Size: 51mm