Agilent Technologies

Compare Tool

Select up to 3 products

All Products

Agilent Technologies General Chromatography

1 - 32 of 63
Sort
View
Show
  • Economy Indicating Refillable Moisture Traps

    Agilent Technologies

    Agilent Indicating Moisture Traps are designed to remove water, oil, and organics from gases employed in, but not limited to, gas chromatography. Refillable moisture traps are constructed from Lexan brand polycarbonate tubing. Lightweight, chemically resistant and of superior strength when compared…

  • Liner O-Rings

    Agilent Technologies

    Agilent fluorocarbon liner O-rings Liners are sealed in the inlet with O-rings or graphite seals Graphite seals are used when inlet temperatures exceed 350°C Fluorocarbon O-ring seals are easier to replace than graphite that deforms and flakes apart Pre-cleaned, then conditioned to eliminate…

  • Fused Silica Tubing Cutters

    Agilent Technologies

    Conveniently designed, pencil-shaped tool and a ceramic wafer that allow you to make clean and easy cuts in fused silica, glass and aluminum-clad capillary columns.

  • Hydrocarbon/Moisture Traps

    Agilent Technologies

    Adsorbent refiles for hydrocarbon/moisture traps allow continued removal of extremely low levels of both moisture and hydrocarbons. Refill supplies material for two recharges for HMT trap.

  • Agilent Choice Liners

    Agilent Technologies

    Agilent’s engineering and testing efforts focus on these parameters when designing liners for Agilent inlet systems. Intensive liner development and testing have resulted in a set of liners that are recommended whenever new methods are being developed, when methods are being optimized, or…

  • Big Moisture Traps

    Agilent Technologies

    Ultra-high capacity for moisture Capacity 130 g H2O Pressure up to 250 psig Reduce H2O to ≤5 ppb 750 cc gas purifiers Refillable Suitable for bulk purification applications or where several instruments are plumbed from a single gas source.

  • Gas Cylinder Regulators

    Agilent Technologies

    Brass body, dual stainless steel diaphragms These regulators and Agilent’s broad spectrum of in-line filters, combination traps, and gas purification systems are an excellent combination to plumb your systems.

  • MicroMist Nebulizer (Glass)

    Agilent Technologies

    Nebulizer, MicroMist, borosilicate glass, standard with Agilent 7700x/e, 8800 and 7500cx/ce series ICP-MS, for most sample types except those containing hydrofluoric acid or suspended particulates.

  • Oxygen/Moisture Traps

    Agilent Technologies

    Oxygen/moisture adsorbents team up to give you two functionalities in the same trap Optimized for maximum surface area and capacity Leak-free, one-piece design (tested to 2000 psi) Bed material treated with ultra-high purity helium Filter design: prevents channeling, promotes efficient…

  • Nuts, Front and Back Ferrule Sets

    Agilent Technologies

    2713J65 connector is required for plumbing 1/4 in. tubing to regulators. Kit includes the following: Ten 1/8 in. nuts, brass Ten 1/4 in. nuts brass Ten 1/8 in. front ferrules, brass Ten 1/4 in. front ferrules, brass Ten 1/8 in. back ferrules, brass Ten 1/4…

  • Tubing Cutter

    Agilent Technologies

    Tubing cutter, for plastic or PEEK tubing.

  • Big Hydrocarbon Traps

    Agilent Technologies

    Capacity: 80 grams of medium to heavy molecular weight hydrocarbons Pressure: Up to 250 psig Efficiency: reduction of C4 hydrocarbons to less than 15 ppb 750 cubic centimeter gas purifiers Ideal for bulk purification applications or where several instruments are plumbed from a…

  • GC Installation Kits

    Agilent Technologies

    Agilent Installation Kits for GC are designed to provide you with the essential items necessary for a successful installation while providing a substantial cost savings over individual purchases. GC Basic Installation Kit: Includes copper tubing, column nuts, two moisture traps, and five wrenches.

  • Nuts

    Agilent Technologies

  • Fast Switch Capillary

    Agilent Technologies

    For 6120 VL+, 6130 SL, 6140 SL-HT.

  • Chemical Filters/Traps For 5890

    Agilent Technologies

    These filters are packed with molecular sieve 5Å, 60/80 mesh, and can be reconditioned by heating in the GC oven.

  • Standard Needle Seat

    Agilent Technologies

  • VHP Fittings

    Agilent Technologies

    Agilent's 1200 bar removable fitting (for 1/16 in od capillaries) consists of a stainless steel screw, an internal stainless steel ferrule and a front ferrule in PEEK. The fitting can be used throughout the flow path, but because it can be re-used without losing tightness, it is especially…

  • Hydrocarbon Traps

    Agilent Technologies

    Remove organics from carrier gases, air and hydrogen High capacity 200 cc of filtering media Impregnated carbon filter media Refill includes media for two recharges of HT200 Series Hydrocarbon Trap

  • LC Tools

    Agilent Technologies

    Thomas offers a selection of high-precision, high-quality, stainless steel tools, from Agilent Technologies to avoid any deformation of the screws or nuts.

  • Split/Splitless Injection Port Kit

    Agilent Technologies

    Kit Inlcudes: Gold plated seal kit, includes washer Replacement for 18740-20885, 3 each Liner, split, with cup, glass wool and packing, 3 each Liner, split, straight, glass wool, non-deactivated, 3 each Column ferrule installation tool Blanking plug, finger-tight…

  • Ferrule Tools

    Agilent Technologies

    Ferrule Tools Tools are designed to remove ferrules stuck inside fittings. Screw the stainless steel ferrule tool into the ferrule and pull it out. Use the smaller capillary ferrule tool for capillary column ferrules (0.32 mm ID column and smaller). The megabore ferrule tool is for megabore…

  • Seal Cap Assembly

    Agilent Technologies

  • General Laboratory Tools

    Agilent Technologies

    The General Laboratory Tool Kit (2714M23) includes the following items: Toolbox Flashlight 8 in. bastard file 6 in. adjustable wrench 12 in. adjustable wrench for use with regulator No. 1 pt, 3 in. Pozidriv shaft, fits no. 2-4 screws No. 2 pt, 4 in. Pozidriv shaft, fits no. 5-10 screws …

  • Snoop

    Agilent Technologies

    Leak test most pressurized gas systems. We recommend that leak detecting solutions be used with care where there is any possibility of the fluid being aspirated into gas flow streams supplying the column or detector. This squeezable bottle comes with a “Snooper Tube” extendable up to 12…

  • Molecular Sieve 13X and Indicating 4

    Agilent Technologies

    Available in three different sizes Mixed packing bed prevents improper installation Easily refillable Tested to 150 psi (helium) Both inlet and outlet connectors are equipped with stainless steel frits to prevent particulates from entering the gas stream. Indicating 4Å…

  • Nickel (Ni) Skimmer Cone

    Agilent Technologies

    Nickel (Ni) skimmer cone used with x-lens for ICP-MS, standard cone with Agilent 7700x/e and 8800 ICP-MS,but also suitable for other 7700/8800 series ICP-MS, use with Ni sampling cone.

  • Inlet and Outlet Valves

    Agilent Technologies

    Agilent produce a variety of inlet and outlet valves designed to ensure the ongoing stability and performance of pump systems in LC applications. Manufactured to Agilent's high levels of quality, security and integrity; LC inlet and outlet valves can be provided for a range of LC pumps. Active…

  • Glass Indicating Moisture Traps

    Agilent Technologies

    Suitable for GC/MS Systems, Electron Capture Detectors, and Electrolytic Conductivity Detectors Molecular Sieve 13X and a band of Indicating Molecular Sieve 4Å Available in 70 cc, 100 cc and 250 cc sizes Heavy wall borosilicate glass tube — no moisture diffusion …

  • Capillary and Fittings Kits

    Agilent Technologies

    Agilent starter kits contain the most often used capillaries and fittings. We included our genuine flexible stainless steel capillaries to make the best connection in your LC system, no matter the brand. The kits are for use with 3-4 or 1-2 mm ID columns, as well as for Micro LC columns. The free…

  • Capillary Column Rinse Kit

    Agilent Technologies

    Solvent rinsing removes many contaminants that accumulate in columns. The contaminants are removed by passing solvents through the column. Only bonded and cross-linked phase columns should be rinsed, or permanent damage to the column will result.

  • High Intensity UltrAA Single Element Lamps

    Agilent Technologies

    UltrAA lamps are high-intensity, boosted discharge hollow cathode lamps. They use the standard lamp current, but apply an additional boost discharge within the lamp.

Compare Tool

Select up to 3 products

Please Log In

Don't have an Account? Create one now.