General Chromatography Hardware

Compare Tool

Select up to 3 products

HomeAll Products

General Chromatography General Chromatography Hardware

1 - 32 of 74
Sort
View
Show
  • Tube Fittings, Union Tees

    Swagelok

    Connect fractional tubing Available in brass or stainless steel

  • Meter Valves

    Swagelok

    2000 psig pressure rating Temperature rating - 149°C (brass), 204°C (stainless) 1/8“ and 1/4“ tube fittings Metering valves gives very fine control of gas flow between 100 and 800 cc/min. Valve is not designed for shutoff service. The handle dead stop is factory…

  • Tube Fittings, Reducing Unions

    Swagelok

    Connect fractional tubes

  • Tube Fittings, Male Connectors

    Swagelok

    Connect fractional tubing to female NPT thread

  • Ferrule Tools

    Agilent Technologies

    Ferrule Tools Tools are designed to remove ferrules stuck inside fittings. Screw the stainless steel ferrule tool into the ferrule and pull it out. Use the smaller capillary ferrule tool for capillary column ferrules (0.32 mm ID column and smaller). The megabore ferrule tool is for megabore…

  • Tube Fittings, Caps and Plugs

    Swagelok

    Caps close end of fractional tubing Plugs close unused port of fractional tubing Available in brass or stainless steel

  • Tubing Cutter

    Agilent Technologies

    Tubing cutter, for plastic or PEEK tubing.

  • Sep-Pak C18 Classic Cartridge

    Waters

    Silica-based bonded phase with strong hydrophobicity; used to adsorb analytes of even weak hydrophobicity from aqueous solutions; typical applications include drugs and their metabolites in serum, plasma or urine, desalting of peptides, trace organics in environmental water samples, organic acids…

  • Fused Silica Tubing Cutters

    Agilent Technologies

    Conveniently designed, pencil-shaped tool and a ceramic wafer that allow you to make clean and easy cuts in fused silica, glass and aluminum-clad capillary columns.

  • Agilent Ni sampling cone for x-lens, ICP-MS, 1/p - 58

    Agilent Technologies

  • Ultra-Torr Vacuum Fittings

    Swagelok

    Attain reliable vacuum sealing, even after repeatedly disconnecting and reconnecting Ultra-Torr straights and tees for vacuum sealing.

  • Tube Fittings, Unions

    Swagelok

    Connect fractional tubing sections. 2713C02 to C16 are brass 2713C21 to C27 are stainless steel

  • Nuts, Front and Back Ferrule Sets

    Agilent Technologies

    2713J65 connector is required for plumbing 1/4 in. tubing to regulators. Kit includes the following: Ten 1/8 in. nuts, brass Ten 1/4 in. nuts brass Ten 1/8 in. front ferrules, brass Ten 1/4 in. front ferrules, brass Ten 1/8 in. back ferrules, brass Ten 1/4…

  • Tube Fittings, Female Connectors

    Swagelok

    Connect fractional tubing to male NPT thread 2713B01 to B27 are brass 2713B32 to B44 are stainless steel  

  • Chromatography Nuts

    SGE

    Spanner (wrench) sizes and uses: 3/16" for use with mini unions, 1/4" for use with 1/16" nuts, 5/16" for use with micro control valves. For standard nuts use reducing short ferrules. For extended nuts use straight or reducing ferrules.

  • VHP Fittings

    Agilent Technologies

    Agilent's 1200 bar removable fitting (for 1/16 in od capillaries) consists of a stainless steel screw, an internal stainless steel ferrule and a front ferrule in PEEK. The fitting can be used throughout the flow path, but because it can be re-used without losing tightness, it is especially…

  • Integral Bonnet Needle Valves

    Swagelok

    O, 1, 18, 20, and 26 Series Live-loaded packing system Compact design Working pressures up to 6000 psig (413 bar) Temperatures up to 600°F (315°C)

  • Tube Fittings, Bulkhead Unions

    Swagelok

    Connect fractional tubing

  • General Laboratory Tools

    Agilent Technologies

    The General Laboratory Tool Kit (2714M23) includes the following items: Toolbox Flashlight 8 in. bastard file 6 in. adjustable wrench 12 in. adjustable wrench for use with regulator No. 1 pt, 3 in. Pozidriv shaft, fits no. 2-4 screws No. 2 pt, 4 in. Pozidriv shaft, fits no. 5-10 screws …

  • Tube Fittings, Union Crosses

    Swagelok

    Connect same size fractional tubing Available in brass or stainless steel

  • Capillary Column Rinse Kit

    Agilent Technologies

    Solvent rinsing removes many contaminants that accumulate in columns. The contaminants are removed by passing solvents through the column. Only bonded and cross-linked phase columns should be rinsed, or permanent damage to the column will result.

  • Nupro Plug Valves

    Swagelok

    Fast acting, 1/4 turn shutoff Simple, compact design Design consists of body, plug assembly and handle. Plug and O-ring seals are TFE coated to provide lubrication between plug assembly and the body bore. Valve features very low torque operation. Intermediate valve positions allow forward…

  • Ball Valves

    Swagelok

    2500 psig pressure up to 60°C 1/8" and 1/4" tube fittings Fully open or fully closed operation only Brass or stainless steel valves allow bi-directional flow, have virtually no dead space and are easily cleaned or purged. One-piece body eliminates multiple seal points.…

  • Tube Fittings, 90 Elbows

    Swagelok

    Achieve leak-tight performance with a robust tube grip and vibration resistance. The remarkable dependability of the Swagelok tube fitting has been proven with over 65 years of success, and has been documented in numerous published test reports, including those performed under extreme conditions.

  • Preppy™ 12-Port Vacuum Manifold

    MilliporeSigma

  • Tube Fittings, Bulkhead Union Retainers

    Swagelok

    Hold connector nuts in place while tightening

  • Standard System Capillaries, 400 and 600 bar (1100/1200/1260 Series)

    Agilent Technologies

    Agilent offers an array of Standard System Capillaries to ensure effective operation and maintenance of LC 1100/1200/1260 Series systems.

  • Hexnut Fittings

    SGE

    Stainless steel 10-32 thread fittings use a non-swaging Kel-F™ or PEEK™ replaceable ferrule Inert contact surfaces make them biocompatible Ideal for applications where corrosive solvents are being used Hexnut with Kel-F™ or PEEK™ ferrules are recommended for use…

  • Ultra-Torr Tees

    Swagelok

    Attain reliable vacuum sealing, even after repeatedly disconnecting and reconnecting Ultra-Torr straights and tees for vacuum sealing.

  • Supel™-Inert Multi-Layer Foil

    MilliporeSigma

  • SPME SAMPLING STAND HOLDER & EXTENSION

    MilliporeSigma

Compare Tool

Select up to 3 products

Please Log In

Don't have an Account? Create one now.