Extraction

Compare Tool

Select up to 3 products

All Products

Corning Extraction Extraction Apparatus

1 - 14 of 14
Sort
View
Show
  • PYREX Soxhlet Extractors

    Corning

    Includes an efficient Friedrichs condenser An efficient extraction apparatus for general purpose use Consists of an extractor, a special Friedrichs condenser and a flask, all equipped with Standard Taper joints Condenser tubulation o.d. is 10 mm for 3/8 inch i.d. tubing

  • PYREX® Graduated Funnel, 47 mm, for Assembly with Fritted Glass Support Base

    Corning

    These graduated funnels,are designed for assembly with the fritted glass support base. Cat. No. 33972-B.

  • PYREX Accelerated One-Step Extractor/Concentrator

    Corning

    Modular PYREX Accelerated One-Step extractor-concentrator performs extraction, concentration, and drying with the same apparatus and is designed for use with solvents of heavier specific gravity than sample being extracted.  Extraction and concentration can be done in 1/3 of the time.…

  • PYREX® Extractors With Standard Taper Joints

    Corning

    Condensers have water-jacketed Standard Taper inner joint. Complete with condenser, flask and extraction tube. The low thermal expansion rate means that the PYREX brand extractors can be routinely used in applications requiring protracted heating at temperatures as high as 230°C. The inherent…

  • PYREX® Fritted Glass Support Base, 47 mm, for Assembly of Graduated Funnel

    Corning

    This 47 mm fritted glass support base is designed for assembly with either the 300 mL graduated glass funnel, Cat. No. 33971-300 or 1000 mL graduated glass funnel, Cat. No. 33971-1L.

  • PYREX® Coarse Porosity Fritted Thimbles

    Corning

    These PYREX® coarse porosity fritted thimbles are designed for use in PYREX® Soxhlet extractors when it is desirable to weigh the material extracted or where paper thimbles may be attacked by the chemicals used. For PYREX® extractors and extraction apparatus, see Nos. 3740 through 3880.

  • PYREX® Extra Coarse Porosity Fritted Thimbles

    Corning

    These PYREX® extra coarse porosity fritted thimbles are designed for use in PYREX® Soxhlet extractors when it is desirable to weigh the material extracted or where paper thimbles may be attacked by the chemicals used. For PYREX® extractors and extraction apparatus, see Nos. 3740 through 3880. .

  • PYREX® 500mL Kuderna-Danish Concentrator Apparatus without Hooks

    Corning

    These 500mL PYREX® Kuderna Danish Concentrators are supplied with Keck clamps instead of spring hooks. The complete apparatus consists of a 3-Ball Snyder column (with 24/40 Standard Taper joints), a 500mL flask (with 24/40 Standard Taper top and 19/22 Standard Taper lower joint), and a…

  • PYREX® 45mm Diameter Coarse Porosity Fritted Thimble, 130mm Long

    Corning

    These 45mm diameter PYREX® coarse porosity (40 to 60µm) fritted thimbles are designed for use in PYREX® Soxhlet extractors when it is desirable to weigh the material extracted or where paper thimbles may be attacked by the chemicals used. These medium length thimbles are 130mm long. For PYREX®…

  • PYREX® 1L One Piece Continuous Heavier than Water Liquid/Liquid Extractor System

    Corning

    This 1L PYREX® single piece continuous liquid/liquid extractor is for use with solvents of heavier specific gravity than sample liquid being extracted. It is designed to meet EPA test method requirements outlined by SW-846, RCRA, and CLP. The sidearm is sealed to the extractor body just below the…

  • PYREX® 1L Kuderna-Danish Concentrator Apparatus without Hooks

    Corning

    These 1L PYREX® Kuderna Danish Concentrators are supplied with Keck clamps instead of spring hooks. The complete apparatus consists of a 3-Ball Snyder column (with 24/40 Standard Taper joints), a 1L flask (with 24/40 Standard Taper top and 19/22 Standard Taper lower joint), and a graduated 25mL…

  • PYREX® Replacement Extractor Body for the One Piece Continuous Heavier than…

    Corning

    This PYREX® extractor body with a 45/50 Standard Taper outer top joint and a 24/40 Standard Taper inner bottom joint is a replacement for the One Piece Continuous Heavier than Water Liquid/Liquid Extractor System.

  • PYREX® Sidearm for the Modular Continuous Heavier than Water Liquid/Liquid…

    Corning

    This PYREX® sidearm has a top 35/25 Spherical Joint socket joint and a middle 18/9 Spherical Joint socket joint and a bottom 24/40 Standard Taper outer joint. It is a component of the modular Continuous Heavier than Water Liquid/Liquid Extractor (Nos. 3922-M and 3924-M).

  • PYREX® 1L Extractor Body for the Modular Continuous Heavier than Water Liquid…

    Corning

    This 1L PYREX® extractor body has a 45/50 Standard Taper outer top joint, a middle 35/25 Spherical Joint ball joint and a bottom 18/9 Spherical Joint socket joint. It is a component of the modular Continuous Heavier than Water Liquid/Liquid Extractor (Nos. 3922-M and 3924-M) and…

Compare Tool

Select up to 3 products

Please Log In

Don't have an Account? Create one now.