High efficiency coil condenser especially suited for vacuum applications. Coil length is 70mm. With 14/10 inner and outer joints; outer joint is externally threaded to allow an O-RING-CAP-SEAL connection with mating inner joint. Supplied with cap and O-Ring.

Cold Finger accessory for standard distilling heads and systems. This cold finger has an inner joint that fits inside the upper outer joint and tube to provide added cooling ability and faster condensation. Fits into 6606, 6609, and 6613 distillation h

Double jacketed with standard taper inner and outer joint at bottom and top.

Dewar type condenser for use with dry ice or other solid cooling agents. Upper tube is 12mm O.D. At bottom is standard taper 24/40 inner joint.

Bulb type, approximately one bulb per 50 mm, with 24/40 standard taper inner joint at bottom.

Designed for small chemical applications. Improved design permits greater condensing capacity. Condenser approximately 139mm jacket length. Joint between condenser and extractor is 24/25. Flask joint is 14/20. Designed to accommodate paper thimble, size 10 x 50 mm. Flask is 30mL capacity. Hose…

With standard taper 24/40 outer joint at top. Jacket length 300 mm. Hose connections are size D.

Microscale sublimation adapter with vertically adjustable condenser tube that allows use with 3 mL, 5 mL, and 10 mL microscale vessels. Two-piece adapter features a #7 Ace-Thred at top of vacuum adapter that, with Nylon bushing and O-Ring, forms a compression seal with condenser tube, bottom 14/10…

With molded spiral condensing surface and joint at bottom and top. Jacket length 250mm. Available in various joint sizes with hose barbs or Ace-Safe connectors.

Bulb type, approximately one bulb per 50 mm, with standard taper 24/40 inner and outer joint at bottom and top, #7 Ace-Thred and Ace-Safe PTFE hose connections on inlet and outlet with barb for 1/4" I.D. tubing. For replacement connectors, see 5853.

Highly efficient. May be used either for through condensation or refluxing. Internal baffling acts as impinging surface for entrained particles and discourages diffusion loss. Available with hose barbs or Ace-Safe connectors.

No Hold Up West condenser available with hose barbs or Ace-Safe connectors.

Microscale air condenser normally used in reflux experiments. When packed with desiccant material, condenser becomes a drying tube. With inner joint at bottom, outer joint at top. Codes -10, -14 and -17 supplied with drip tip for use with 9595 Spinning Band Column. Effective length, approximately…

With water cooled standard taper 24/40 inner and outer joint at bottom and top. Hose connections are size D.

Reflux controlled by regulating jacket temperature. Provides compact spiral path for condensation. Jacket length 200mm. Bottom standard taper 24/40 joint.

Double-jacketed, with standard taper 24/40 inner and outer joint at bottom and top. Extra cooling capacity for volatile materials. Compact design retards diffusion. With #7 Ace-Thred and Ace-Safe PTFE hose connections on inlet and outlet with barb for

High through-put, double coil condensers are designed to fit larger systems and pilot plant reactors. The design is similar to a rotary evaporator type condenser, where large volumes of material are being condensed at high temperatures and where large

Bulb type, approximately one bulb per 50 mm, with various joint sizes at bottom and top. Available with hose barbs or Ace-Safe connectors.,/p>

Jacket length is measured from the lower shoulder of the bulb to the bottom of the finger. Diameter of tube is 14mm. Used in 6472 Pilot Plant Reactor.

With straight inner tube sealed through the jacket. This condenser is acceptable for use with Abderhalden or Mini-Lab moisture test apparatus.

With molded spiral condensing surface and standard taper 24/40 inner joint at bottom. Top tubulation tooled to take No. 3 stopper. Jacket length 250mm. Hose connections are size D.

With top joint jacketed for water cooling. Jacket length measured from bottom of top joint.

With standard taper 24/40 inner joint at bottom. Jacket length 300mm. Hose connection is size D.

With 110mm jacket length, also an additional vacuum takeoff between outer joint and jacket.

Code -23 for use with 9718 Reactor. Outside diameter is 10mm or 14mm to fit #11 or #15 Ace-Thred respectively. Water connection tubing is 5mm O.D. Overall length, 200mm.