Ace Glass

Columns, Ace Glass

Compare Tool

Select up to 3 products

1 - 32 of 40
Sort
View
Show
  • Column, Chromatography

    Ace Glass

    Rugged columns with internally threaded ends to which a wide choice of upper and lower end pieces can be fitted using 5837, 5838, 5841, 5842, and 5843 fittings. Available in a variety of lengths and diameters. Some sizes available with epoxy coating for added protection against scratches.

  • Column Head

    Ace Glass

    For use with 5862 Chromatography Column.With #50 Ace-Thred center neck and/or two #15 Ace-Thred side necks and 4" or 6" flange at bottom, ground flat Use with 6517 Clamp.

  • Column, Chromatography, with fritted disc

    Ace Glass

    Column has standard taper 24/40 joint at top and 2 mm bore stopcock at the bottom with Por. B (70-100m) fritted disc sealed into the bottom of tube.

  • Column, Flash Chromatography, Spherical Joint, Epoxy Coated

    Ace Glass

    Simple absorption chromatography column for rapid preparative separations with moderate resolution. Allows separations of samples from 0.01 to 10.0g in 10-15 minutes. Column and reservoir, only, are Epoxy Coated. Reservoir connects between column and flow control adap-ter. Joints on column,…

  • Column, Flash Chromatography, Standard Taper Joint, Epoxy Coated

    Ace Glass

    Simple absorption chromatography column for rapid preparative separations with moderate resolution. Allows separations of samples from 0.01 to 10.0g3 in 10-15 minutes. Column and reservoir, only, are Epoxy Coated. Reservoir connects between column and flow control adap-ter. Joints on column,…

  • Safety Shield, Plastic, Michel-Miller

    Ace Glass

    Acrylic safety shield and polyethylene cap for use with Michel-Miller Columns to insure safe operation at pressures to 300 psi. Top thread of column is hung in polyethylene cap; cap is then held by the plastic shield. Clamp the shield, not the column.

  • Rapid Preparative Chromatography System

    Ace Glass

    Rapid preparative chromatography system suitable for use to pressures of 50 psig, operation behind a shield is recommended. Resevoir is 2L or 3L capacity, epoxy coated and pressure tested. Complete item includes:Brass or glass manifold, pressure gauge, pressure relief valve, column, tubing, and…

  • Chromatographic Column, With Filter Disc

    Ace Glass

    Chromatographic column with 24/40 joint at top, 2 mm bore 1:5 taper solid PTFE stopcock plug at bottom and porosity B (70 - 100 m) fritted disc sealed near bottom of tube. These columns also appear in expanded listing under 5871.

  • Filter Column, Michel-Miller

    Ace Glass

    For use with Michel-Miller Liquid Chromatography System as filter to assure only clean solvent enters column. Threads are #7 Ace-Thred for use with 5801-07 End Fitting. Usually positioned, in line, between pump and column using 1/4"-28 tubing connectors such as 5854, 5855 or 12724. Glass only is…

  • Chromatographic Column, 1:5 PTFE Plug, Flow Control Connection

    Ace Glass

    Chromatographic column with integral reservoir for connecting 5872 Flow Control Adapter. With 2mm bore, 1:5 taper solid PTFE stopcock plug at bottom. Available with or without porosity B (70 - 100 m) fritted disc sealed in. Order column, flow control adapter and clamp separately.

  • Chromatographic Column, 1:5 PTFE Plug

    Ace Glass

    Chromatographic column with integral reservoir at top, and 2 mm bore 1:5 taper PTFE stopcock plug at bottom. Opening at top is either 24/40 outer joint or opening for #3 stopper. Available with or without porosity B (70-100micron), fritted disc sealed in.

  • Chromatographic Column, 1:5 PTFE Plug, With 24/40 Joint

    Ace Glass

    Chromatographic column with 24/40 standard taper joint at top and 2mm bore 1:5 taper solid PTFE stopcock plug at bottom. Column supplied with 7506-06 Nylon bushing and FETFE O-Ring. Complete item consists of column with bushing and O-Ring, and 5853-07 Tubing Connector for connecting 12.5 to 14mm…

  • Column, Flash Chromatography, Epoxy Coated, Modified

    Ace Glass

    Simple absorption column for rapid preparative separations with moderate resolution. Modified with a #25 Ace-Thred connector in place of 35/20 joints, for grease free connection. Internally threaded connector & Nylon bushing make a pressure-tight, O-Ring compression seal with glass stem on…

  • Column, Chromatography

    Ace Glass

    With 24/40 standard taper joint at top and a 2 mm bore stopcock at the bottom.

  • Column, Injection Reservoir

    Ace Glass

    Chromatography accessory pre-column and injection reservoirs.

  • Column, Chromatography, Epoxy Coated, Michel-Miller

    Ace Glass

    High performance, non-packed, low pressure liquid chromatography columns, epoxy-coated. Simple to assemble, PTFE (no O-rings), safe operation to 150psi with safety shield. Usable with various packing materials chemically inert, zero dead volume, leak free. For analytical or preparative…

  • Adapter, Bottom Drip

    Ace Glass

    Drip tip for chemical type chromatography. I.D. of drip approximately 4 mm. Size listed is Ace-Thred designation which refers to I.D. of tubing above thread and corresponds to 5820 column diameter.

  • Adsorption Column

    Ace Glass

    Used in ASTM D1319-65T, a "test for hydrocarbon types in liquid petroleum products." Consists of a charger section with a capillary neck, a separator section, and an analyzer section. Upper joint spherical 28/12.

  • Adjusta-chrom, Column, Michel-Miller

    Ace Glass

    A combination of the high performance, low pressure Michel-Miller Chromatography Line and Adjusta-Chrom Recycling Column. Top has adjustable fitting that allows for a bed height anywhere within 1 - 6" below thread. Plunger tip is all PTFE with a porosity C (25-50m) glass disc. Complete column…

  • Chromatographic Column, With Fritted Disc

    Ace Glass

    Chromatographic column with 2mm bore, 1:5 taper solid PTFE stopcock plug and porosity B (70 - 100 m) fritted disc sealed in.

  • Chromatographic Column, Plain

    Ace Glass

    Plain, open top, chromatographic column, universally suitable for many separations.

  • Chromatographic Column, 1:5 PTFE Plug

    Ace Glass

    Chromatographic column with 2mm bore 1:5 taper solid PTFE stopcock plug at bottom.

  • Adapter, Injection Port, Michel-Miller

    Ace Glass

    A simple, all PTFE septum injector. Allows direct, on-column injection to the center of the filter disc at top of column without stopping the solvent flow through the 1/4"-28 female side thread (with or without helicoil). Locknut design provides leaktight seal without o-rings. You can order the…

  • Adapter, Small Sample Injection and Feed Tube

    Ace Glass

    Column adapter for small sample injection including feed tubes.

  • Float, Polyethylene

    Ace Glass

    Used on top of column packing to prevent turbulence caused by drop-wise addition. Six per pkg.

  • Adjusta-chrom, Recycling Column

    Ace Glass

    Adjustable bed chromatographic column used for recycling, ascending or descending applications allowing for quick and easy adjustment of the PTFE plunger. The Por. C (25-50m) glass disc gives rapid flow with a minimum of mixing. Pressure tight to 3.515 Kg/cm2 (50 psi) at room temperature or…

  • Chromatographic Column, With Filter Disc And #15 Ace-Thred

    Ace Glass

    Chromatographic column with 2mm bore, 1:5 taper solid PTFE stopcock plug and porosity B (70 - 100 m) fritted disc sealed in at bottom and #15 Ace-Thred at top of column. Column supplied with 7506-06 Nylon bushing and FETFE O-Ring. Complete item consists of column with bushing and O-Ring and 5853-07…

  • Chromatographic Column, 1:5 PTFE Plug, With #15 Ace-Thred

    Ace Glass

    Chromatographic column with #15 Ace-Thred at top and 2mm bore 1:5 taper solid PTFE stopcock plug at bottom. Column supplied with 7506-06 Nylon bushing and FETFE O-Ring. Complete item consists of column with bushing and O-Ring, and 5853-07 Tubing Connector for connecting 12.5 to 14mm O.D. tubing to column.

  • Funnel, Addition

    Ace Glass

    For charging columns. The capacity is approximately 5 times the largest column volume. Size listed is Ace-thred designation which refers to I.D. of tubing above thread and corresponds to 5820 column dia- meter. Available in cylindrical or conical shapes.

  • Adsorption Column

    Ace Glass

    Used in ASTM D1319-65T, a "test for hydrocarbon types in liquid petroleum products." This unit is fabricated from ACE Trubore tubing. Tip is attached to column by means of a 12/2 spherical joint. Upper joint spherical 28/12.

  • Adapter, Chromatography Column End Fitting, with NPT

    Ace Glass

    For use as column end fitting that allows connection of appropriate size Ace-Thred to tubing connectors with NPT threads. Available in various Ace-Thred and NPT sizes. Most come complete with both a 100 micron and a 350 micron polyethylene filter.

  • Column, Chromatography

    Ace Glass

    Large chromatography columns with o-ring grooved flat flanged tops and Ace-Thred bottoms. Column extenders and 5860 heads should be mated to columns with our 6517 series clamps. All columns and extenders are supplied with either a 7855-254 (4") or 7855-260 (6") silicone o-ring. For capfe o-rings,…

Compare Tool

Select up to 3 products

Please Log In

Don't have an Account? Create one now.