Ace Glass Air Samplers
-
Impinger, Air Sampling
Ace GlassA high velocity impinger (Ref. AGI-4) which passes 12.3 to 12.6L/min. (corrected to engineering standard gas conditions) when the pressure drop across the orifice is 41cm Hg or greater. Stopper fits 24/25 125ml bottle and features a 11mm OD center tube, 8mm OD side arm with bulge, 0.05in capillary…
-
Air Sampling Cane, with Funnel
Ace GlassAir sampling cane with funnel at one end to avoid water droplets from collecting at edge and being sucked into manifold train. Bulge above the funnel is for glass wool or similar material to allow for filtering of particulates. Codes -22 & -26 feature a #7 Ace-Thred port for introducing calibration…
-
Schlenk Tube, NO-AIR
Ace GlassSchlenk style reaction tube for vacuum and No-Air applications. Available in many capacities, joint sizes and side arm configurations including a glass stopcock, 0-3 inlet valve or a 0-4 Hi-Vac valve.
-
Filter Screen
Ace Glass7493 air sampling cane 6.4mm mesh PTFE screen assembly. Only available for our 25mm OD canes. Place the screen within the retaining ring, unfasten the yoke's nut & bolt, pass the now open yoke around the funnel and then tighten the nut and bolt to secure the assembly. The screen is held in place…
-
-
Midget Impinger
Ace GlassUnique impinger designed to be more economical when connecting in series eliminates need for connecting tubes.The 12/5 joints are perpendicular and come directly off bottle 180 degree apart. Screw cap on bottle has PTFE liner. Each bottle has one ball and one socket joint. Capacity 25mL. Bottle is…
-
Impinger, Air Sampling
Ace GlassA high velocity impinger (Ref. AGI-30) which passes 12.0 to 13.0L/min. (corrected to engineering standard gas conditions) when the pressure drop across the orifice is 41cm Hg or greater. Stopper fits 24/25 125ml bottle and features a 11mm OD center tube, 8mm OD side arm with bulge, 0.05in capillary…
-
Bubbler, Smog
Ace GlassBubbler with either fritted tip or plain orifice stopper. Bottle has 24/40 joint and 10 cm tube below bulge. Stopper has 12/5 outer joint on inlet arm and 12/5 inner on outlet arm. Fritted tip is porosity C (25-50m). Orifice tip is 1.5mm capillary with end tapered. Approximate capacity, with…
-
FLASK Reaction/Storage NO-AIR
Ace GlassSchlenk style flask for vacuum, NO-AIR or gas applications. Can be used for storage or reactions. Top is either a no.15 o-ring or outer standard taper joints. Side arm has either a 0-3 inlet valve or a 2mm or a 4mm glass stopcock.
-
Manifold, Vacuum
Ace GlassGlass Manifold with #15 Ace-Thred at either end To allow switching 5853 vacuum connection to left or right side. Supplied with three or five, 4mm straight bore PTFE stopcock sampling ports. (Additional ports can be ordered.) Overall length of glass manifold is 230mm. Complete item consists of 8763…
-
Increased sensitivity and versatility over other models, mercury requirement is reduced to 20-30cc. A control point within 1mm Hg can be fine-tuned by adjusting the height of the pump-out tubulation. The Cartesian driver float drops away from pump-out orifice on an increas- ing system pressure and…
-
Borosilicate glass vacuum/NO-AIR trap. Simliar to 8755 traps but with No. 15 O-Ring side connecting joints. Ideal for vacuum cart and other vacuum or NO-AIR applications. Comes complete with stainless steel ball-joint clamp and Viton O-Ring.
-
Midget Bubbler
Ace GlassIdentical to 7531-10 with the exception that the nozzle is replaced by a sintered glass filter, porosity A (145-175 microns). Used in determination of Acrolein: 4-Hexylresorcinol Method #1. Bottle has encircling graduations from 0 to 25mL or 0 to 30mL in 5mL divisions. Inlet/ outlet are 7mm O.D.…
-
Impinger, Air Sampling
Ace GlassA high velocity impinger air sampling which passes 6L/min (corrected to engineering gas conditions) when the pressure drop across the orifice is 41cm Hg or greater. Stopper fits 24/25 125ml bottle and features a 11mm OD center tube, 8mm OD side arm with bulge, 0.035in capillary tip that is…
-
Permanent split capacitor, steel housed blower used to pull air through our Air Sampling manifolds. Blower produces 50 cfm @ 0.0 meters of water static pressure which assures a minimum pressure drop across each port in the manifold train. Free air rpm is 3030. Available in both 115 & 230v…
-
Valve, Pressure Release, Automatic
Ace GlassAutomatic, adjustable pressure release valve for safer operation of pilot plant or other assemblies where the pressure is of great concern. The tension on the stainless steel spring determines the amount of pressure needed to force the lower piece open. With the spring supplied, the range is 15-50…
-
Imhoff Cone, Sedimentation
Ace GlassImhoff sedimentation cone for the determination of settleable matter in water. Either blunt tip or Ace-Thred tip for environmental applications. Graduated from 0-2ml in 0.1ml divisions, 2-10ml in 0.5ml divisions, 10-40ml in 1ml divisions, 40-100ml in 2ml divisions.
-
Adapter, Bleed, Air Sampling
Ace GlassAdjustable bleed adapter used for reducing air flow in the Air Sampling Manifold to prevent a pressure drop across the sampling ports. Normally installed in front of the 7511 blower, in line with the manifold. Positioning of holes in threaded nylon plug controls the volume of air flow. Plug…
-
Valve, Rapid Purge, Firestone
Ace GlassA rapid, efficient and foolproof Purge Valve for 100% replacement of air in reaction vessels with any desired gas (N2, H2, Ar, Cl2, etc.). No mercury used, no reducing valve needed on gas source, no high vacuum source necessary. No need to watch manometers, hand control gas flow, or install warning…
-
Air Sampling Sweep Elbow
Ace GlassSweep elbow, available with one end threaded, the other end reduced for use with 7506 bushing or both ends threaded for use with either 7506 bushing or 5841 coupling.
-
25mm Blower Mount
Ace GlassAluminum blower mount for connecting 7511 blower to glass manifold. With threaded stock.
-
Manifold, O-Ring Joint Ends
Ace GlassSingle tube vacuum manifold with #15 o-ring joint ends. Available with 3 or 4 high vacuum stopcock ports. Order with inner joint port ends (14/20 or 24/40) or #15 o-ring joints. The distance between ports is 95mm, ideal for flasks up to 250mL. Please see our various o-ring joint adapters such as…
-
Air Sampling Cane, Straight
Ace GlassStraight tube type air sampling cane with polyethylene hood and stainless steel brackets. Codes -35 & -37 feature a #7 Ace-Thred port for introducing calibration gases.
-
Manifold, Double Tube, O-Ring joint ends
Ace GlassDouble tube vacuum manifold with 4 x #15 o-ring joint ends. Available in 3 or 4 port configuration with Easy Action 0-10MM stopcocks. The ports can be ordered with either 14/20, 24/40 inner joints or #15 o-ring joints. Distance between ports is 100MM which will allow for flasks up to 250mL. Please…
-
Filter Support Assembly
Ace GlassFilter support assembly for collecting dust particles in a stack sampling system. Available in either 51mm (2"), 76mm (3") or 102mm (4") (illustrated) size. Consists of: PART A, with 28/15 outer joint bent perpendicular to flow path; PART B, with seat for fritted disc and 28/15 inner…
-
Storage Tube, Schlenk
Ace GlassGraduated Schlenk storage tube with 14/20 or 24/25 outer top joints, 14/35 or 24/40 inner joint side arms, stopcock inlet or hose barbed inlet valve. Reaction accessories include 7759 series filter tubes, 7807 series finger condenser, 9543 series stoppers and 13657-33 stirring magnet..
-
Midget Impinger
Ace GlassImpingers used for sampling small air volumes at low velocities. Bottle with 24/40 stopper joint is available in 25 or 30ml sizes. The stopper is available with an open nozzle or one calibrated to deliver 0.09 to 0.11 CFM at 30.5cm (12in) vacuum. The stopper inlet is available as an open tube end,…
-
Impinger, Sherer
Ace GlassConsists of bottle with hex base and 45/50 joint, SO2 bubbler stopper with 25 mm diameter Por. C (25-50m) fritted disc, and impinger stopper. Capacity, 275mL. Inlet/outlet are 8mm.
-
Vacuum, NO-AIR adapter for vacuum cart, vacuum manifolds and Schlenk lines. Has No. 15 O-Ring joint side port with a Hi-Vac valve for precise flow control and an ACE-THRED bottom outlet.
-
Adapter, Vacuum Take-off
Ace GlassThomas No. 1165A11 14/20 vacuum adapter, 30mm stem below the joint. Thomas No. 1165A12 14/20 vacuum adapter, 175mm stem below the joint. Thomas No. 1165A13 19/22 vacuum adapter, 30mm stem below the joint.
-
Schlenk Tube, NO-AIR
Ace GlassSchlenk style reaction tube for vacuum and No-Air applications. Available in many capacities, joint sizes and side arm configurations including a glass stopcock, 0-3 inlet valve or a 0-4 Hi-Vac valve.
-
Check Valve
Ace GlassAn all-glass check valve with ground seat for liquid seal. Available in style A for vertical use, and style B for right angle connection. Connections are 8mm O.D.