Protects water baths and other water systems against the growth of algae, bacteria, molds and biofilms. Just 2ml per liter of water adds a blue tint which will fade after about 3 months reminding you to change the water and add new conditioner. Protects pumps and thermostats and helps…

Ethylene glycol and propylene glycol are the primary ingredients in commercially-available antifreezes. They are used with various corrosion inhibitors to protect metal surfaces in cooling water systems. CHEMetrics glycol kits are used to monitor potable waters for glycol contamination…

Method Dissolved carbon dioxide (CO₂) is naturally present as a result of animal respiration, the decay of organic matter, and the decomposition of certain minerals. It is the major source of acidity in unpolluted water samples. Surface waters typically contain less than 10 ppm…

Hardness is a measure of the mineral content of water. Calcium and magnesium are the most common minerals that contribute to hardness. Hard water causes scaling in boilers and other industrial equipment, and diminishes the effectiveness of soaps and detergents. The EDTA Method (Total) …

Octet Comparator Method For determining hexavalent, trivalent, and total chromium Octet comparator has color standards representing 0.1, 0.2, 0.4, 0.6, 0.8, 1.0, 1.2 and 1.5 ppm Cr Sufficient for 20 tests Test requires suitable hot plate, not included Reagent Refill only. …

UN Number: UN3316

UN Number: UN3316

The Lovibond® calcium hardness calcio no. 1/no. 2 tablet set is suitable for use in research facilities and chemical laboratories to conduct wide range of experiments. It is available in sturdy bottle that endures heavy and rigorous usage. It contains 100 tablets.

The DPD method is elementary for the determination of chlorine and for the correct dosing of the water care product. The DPD No.1 tablet is used to determine the free chlorine. The tablet is placed in a cuvette with a few drops of the water sample and crushed, sample water is added and mixed by…

UN Number: UN2796

Phosphorus occurs naturally in rock formations in the earth's crust, usually as phosphate. High phosphate concentrations in surface waters may indicate fertilizer runoff, domestic waste discharge, or the presence of industrial effluents or detergents. Although phosphates from these sources are…

Sulfides are naturally present in ground waters as a result of leaching from sulfur-containing mineral deposits. Surface waters do not usually contain high sulfide concentrations. Sulfides result from the decomposition of organic matter, from bacterial sulfate reduction under anaerobic conditions…

Molybdate is used throughout the industrial water treatment and power generation industries as a corrosion inhibitor in both open- and closed-loop cooling water systems. In solution, molybdate anions complex with oxidized iron to form a protective film of molybdate and ferric-oxide. Molybdate is…

Hydrazine is a powerful reducing agent that is used in various chemical processes and in boiler water as an oxygen scavenger. To control corrosion, residual hydrazine typically is maintained in the 0.05 to 0.1 mg/L range. Higher levels may be used to guard against corrosion when the boiler is out…

This kit tests for Sodium Nitrite using the Direct Reading Titrator method. Applications: Industrial Water Boiling and Cooling, Water and Wastewater Range/sensitivity is 0-1000 ppm/20 ppm NaNO₂

Consumables & accessories for Sartorius Arium laboratory water systems. Arium® Smart Station flexible remote dispenser Ultrapure Water for benchtop or wall-mounted installation. The Arium® Smart Station is designed for flexible remote dispensing of ultrapure water directly at the…

UN Number: UN3316

UN Number: UN3316

This kit tests for Chloride in fresh water samples using the Direct Reading Titrator method. Applications: Environmental Education, Aquarium and Fish Farming

UN Number: UN3316

This LaMotte Phosphate test kit tests for low range Phosphate using the LRC Comparator. Range and sensitivity is 0, 0.2, 0.4, 0.6, 0.8, 1.0, 1.5, 2.0 ppm PO43-. Applications: Environmental Education

UN Number: UN3316

3322 Octa-Slide Comparator System For determining total sulfide Sufficient for 50 tests NPDES-EPA accepted Unit uses the Pomeroy methylene blue method for analysis. Total sulfide is determined using a color dye, which is added to an un-reacted sample until it matches a reacted…

Carbohydrazide is added to boiler system water as an oxygen scavenger to control corrosion. It is a safer alternative to hydrazine, which is toxic. Carbohydrazide reacts with oxygen at low temperatures and pressures. The products of the reaction are volatile and do not contribute dissolved solids…

No color matching, no look up charts, no guessing! The unique, multi-test ColorQ pool and spa hand-held photometer reads SEVEN test factors (Free Chlorine, Total Chlorine, Bromine, pH, Alkalinity, Calcium Hardness, and Cyanuric Acid) directly on a digital display. Featuring an innovative…

Because of its strong oxidizing properties, chlorine is an excellent biocide used to treat potable waters, municipal wastes, and swimming pools. When used to treat potable water, chlorine helps alleviate the adverse effects of iron, manganese, ammonia, and sulfide. The Maximum Residual Disinfectant…

Replacement LaMotte pH Indicator reagent. This replacement reagent has a bottle size of 2 oz. This pH Indicator Reagent is for use with the ColorQ Digital Photometer Test Kits.

Octet Comparator For determining sulfate in natural waters and waste waters Employs modified APHA turbidimetric method with barium chloride Has color standards representing 20, 40, 60, 80, 100, 120, 160, and 200 ppm sulfate, sufficient for 50 tests

Chloride is the most common inorganic anion found in water and wastewater. The Maximum Secondary Contaminant Level for drinking water for chloride is 250 mg/L. Natural sources of salt are the ocean and various salt deposits above and below ground. Chloride is very corrosive to most metals in…

Method: colorimetric with test strips 0.5 - 1 - 2 - 3 mg/g KOH MQuant™ Storage class: 10 - 13 Other liquids and solids Storage: Store at +15°C to +25°C. Deep-frying causes oils and fats to decompose over time. One of the major by-products of decomposition is free…