The CApture Portable Fuming System quickly fixes latent fingerprints at the crime scene using microburst or traditional CA fuming methods, while protecting the user from hazardous fumes. Its patented* design combines all the components needed in one compact system: a heater to heat the Super Glue†; a shatter-resistant, clear protective chamber to contain the fumes as they react with the latent prints; an exhaust blower; and particulate/carbon exhaust fi lter. No ducting is required. Since prints may be easily developed at the scene, irrelevant evidence may be ruled out thus saving valuable laboratory processing time and storage space.
Features
- Patented* collapsible design
- Clear, polycarbonate chamber, interior dimensions: 8.0" (20 cm) w x 8.0" (20 cm) d x 16.0" (41 cm) high
- Heater with microprocessor-control in one degree increments between 120° to 350° F (50 to 177° C). Temperature of the heater stabilizes at the set point (±15°F) within 3 to 5 minutes
- Two heater receptacles with heater door to accommodate heater pans. Ten aluminum heater pans are included
- Stainless steel support manifold with three control slide slots and perforations for attaching a shelf and hook
- Stainless steel hook, shelf and perforated tray
- Control panel with LCD for displaying set point or actual heater temperature in °F and “Up,” “Down,” and “Set” buttons for programming set point temperature
- Three-way heater/off/vent switch
- Rear-mounted main power switch/circuit breaker
- Leveling foot with locking pin
- Epoxy-coated steel housing
- Built-in exhaust blower
- Particulate/activated carbon fi lter cartridge with MERV 11 rating and capacity for 100 development cycles
- ETL listed (Model 3420000)
- CE conformity marking (Models 3420020, 3420022 and 3420024)
- 6' (1.8 meters) power cord with plug
- Actual weight 24 lbs. (10.9 kg)
- Shipping weight 30 lbs. (13.6 kg)
*Patent-pending
†Super Glue® is a registered trademark of Super Glue
Replacement Aluminum Heater Pans
Disposable aluminum pans for holding Super Glue® or water. Ten pans are included with each CApture Portable Fuming System. Package of 250. Shipping weight 1.0 lb. (0.5 kg)
Replacement Clear Chamber
With latches.Polycarbonate. Shipping weight 12.5 lbs.(4.7 kg).
Replacement Filter Cartridge
Capacity for 100 development cycles. Shipping weight 5 lbs. (2.3 kg).
Exhaust Connection Kit
Allows the Fuming System to exhaust to a remote location, such as out a window or into a nearby fume hood. Includes 10' long, 4" diameter collapsible duct. Shipping weight 1 lb. (0.5 kg).
Stainless Steel Shelf
Allows evidence to be supported in the clear chamber during development. 7" w x 5" d (18 x 13 cm). Type 304 stainless steel. One Shelf is included with each CApture Portable Fuming System. Shipping weight 1 lb. (0.5 kg).
Stainless Steel Hook
Allows evidence to hang inside the clear chamber during development. Type 304 stainless steel. One Hook is included with each CApture Portable Fuming System. Shipping weight 1 lb. (0.5 kg).
Stainless Steel Perforated Tray
May be placed on the Stainless Steel Shelf to support small items of evidence, such as bullet casings. Perforations allow for airfl ow. 7.25" w x 5.25" d (18 x 13 cm). Type 304 stainless steel. One Tray is included with each CApture Portable Fuming System. Shipping weight 1 lb. (0.5 kg).
Field Power Kit for CApture 115V and 230V
Field Power Kit for Capture Portable Fuming System
1221Y17
Electrical Specification: 115 volts, 60 Hz, 1 amp
Electrical Requirements: Domestic
Blower Requirements: Built-in Blower
Power Cord and Plug: 115 volts, 60 Hz
Compliance: ETL
Product Type: Fuming System
1221Y18
Electrical Specification: 230 volts, 50/60 Hz, 0.5 amp
Electrical Requirements: International
Blower Requirements: Built-in Blower
Power Cord and Plug: British (UK)
Compliance: CE
Product Type: Fuming System
1221Y19
Electrical Specification: 230 volts, 50/60 Hz, 0.5 amp
Electrical Requirements: International
Blower Requirements: Built-in Blower
Power Cord and Plug: Schuko
Compliance: CE
Product Type: Fuming System
1221Y20
Electrical Specification: 230 volts, 50/60 Hz, 0.5 amp
Electrical Requirements: International
Blower Requirements: Built-in Blower
Power Cord and Plug: China/Australia
Compliance: CE
Product Type: Fuming System